Stainless Steel propellers - Polish or Antifoul

N

Nigel52

Well-Known Member
Joined
21 Nov 2021
Messages
271
Location
Poole
Visit site
Previously with a sailboat I cleaned and antifouled my propeller. On my RIB and day boat with outboard no issue as propeller out of the water. Currently have been surprised how my stainless steel duo props on an outdrive leg have got so fouled this last season despite a mid season power wash and over the side clean in July & August.

I want to keep the boat in the water and in use April - end of October and need to keep propellers clean otherwise speed drops off by circa 10 knots and fuel consumption jumps.

Would people suggest polishing right up or clean and antifoul. (Planing boat with top speed circa 24 knots and cruising at 28-20 knots)
 
I personally wouldn’t ever think about putting anything on a stainless prop. Precision engineered and finished thing really. Be a shame to loose its efficiency with paint. But I get the other side of the story too. You’d think any growth would find it hard to hold onto a finely finished surface like that, once underway perhaps. Anything on it should come away perhaps ?
 
QBhoy said:
I personally wouldn’t ever think about putting anything on a stainless prop. Precision engineered and finished thing really. Be a shame to loose its efficiency with paint. But I get the other side of the story too. You’d think any growth would find it hard to hold onto a finely finished surface like that, once underway perhaps. Anything on it should come away perhaps ?
Click to expand...
Well I’m currently polishing them both up and hope that this works for next season. As this was my first season with this type of I was keen to get other’s experience.
 
QBhoy said:
I personally wouldn’t ever think about putting anything on a stainless prop. Precision engineered and finished thing really. Be a shame to loose its efficiency with paint. But I get the other side of the story too. You’d think any growth would find it hard to hold onto a finely finished surface like that, once underway perhaps. Anything on it should come away perhaps ?
Click to expand...

It doesn't.

Mine stayed in reasonable shape for a few months, but got horribly fouled mid-season and I had to spend an hour or so in the tender removing it.
 
SC35 said:
It doesn't.

Mine stayed in reasonable shape for a few months, but got horribly fouled mid-season and I had to spend an hour or so in the tender removing it.
Click to expand...
Did the growth remain even after a good run out on her, with the throttles open ?
 
QBhoy said:
Did the growth remain even after a good run out on her, with the throttles open ?
Click to expand...

Earlier in the season, a blast across the Solent would clear the fouling.
But the stuff that attached later in the season didn't seem so willing to fall off.
 
SC35 said:
Earlier in the season, a blast across the Solent would clear the fouling.
But the stuff that attached later in the season didn't seem so willing to fall off.
Click to expand...
Can imagine. It’s a tough one eh. Likely not an option for most…but sitting near a fresh water river estuary with suitable tide state for a wee while can drop growth fairly effectively. Quite amazed at the effect of it.
 
I clean mine once a year with brick cleaner. It's diluted HCl basically. The SS props get jet washed when the boat comes out but mostly its just some reddish growth near the center and a few tube worms on the hub. So, rubber gloves, glasses and rub it on with a bit of old towel. Wash the blades thoroughly after. I don't try to get them looking like new, just clean. It takes perhaps 20 mins for 7 blades on a pair of contra props. I do a few longish 4hrs trips at 23 or 24 kts. That probably helps. Even when dirty it seems to be more cosmetic than a performance issue. I don't think I loose more than a knot.
 
Nigel52 said:
Have you tried this antifoul as would be good to know from user experience.
Click to expand...
I havent to be honest - I was going to get some this winter but a change in circumstance has prevented this.
what I can say is the coating that was on my newer set was clear like the one in the link that I posted earlier.
I did ask volvo about the coating but they didnt reply
 
Anything submerged, especially near the surface where the sun will bring light and higher temperature, will foul.

If the goal is to prevent growth on propellers I can see two ways:

1: Use the boat more frequently
2: Apply antifouling

#2 brings a challenge: Get it to stay on for a full season.

Of the many products I have used (even unorthodox) over 5 decades and 7 boats, the best result has been Hammerite Special Metals primer with Velox on top.
Held up pretty well on current boat, pushing 7½ tons at 24 knots (now and then,- not all the time) ?
 
You must log in or register to reply here.

Share this page

Top