Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
VicS's latest activity
VicS
replied to the thread
Suzuki 2.5 Idle issues/hang despite new gaskets and uktrasonic clean
.
Check that when the twist grip is returned to the idle position the throttle butterfly closes to the idle position. If the cable is...
21 Apr 2024
VicS
reacted to
neilf39's post
in the thread
Beta 20 water leak
with
Like
.
Water pump shaft seal has gone. Just needs replacing.
21 Apr 2024
VicS
replied to the thread
Beta 20 water leak
.
Beaten to it by neilf39. You'll probably find the water is dripping from a weep hole in the pump body. While it is only a drip it's...
21 Apr 2024
VicS
reacted to
srm's post
in the thread
Petty forum members
with
Like
.
For around six months I ran a "signature" saying my boat urgently needed a new owner. This, somewhat indirectly, resulted in said new...
21 Apr 2024
VicS
replied to the thread
Beaches with pubs i can anchor off in the summer nearish to Portsmouth.
.
Is the New Inn open? I thought it had closed permanently.
21 Apr 2024
VicS
replied to the thread
Marine gas engineers in Solent area
.
How sad to read the complaints about Apollo Gas. They took over Gas Check Marine a few years ago. I never saw any complaints about them...
20 Apr 2024
VicS
replied to the thread
Force 5 hp outboard
.
I sounds as though you will need to replace this washer. Maybe a Dowty bonded seal would be an alternative to a copper washer but it...
19 Apr 2024
VicS
replied to the thread
Can a Blake’s seacock be inadvertently installed so it closes anticlockwise?
.
IF they are the Jabsco ones you'll find them here Toilet Accessories / Marine Toilets / Marine / Xylem JabscoShop - Jabsco & Rule Pumps...
18 Apr 2024
VicS
replied to the thread
Force 5 hp outboard
.
If you are saying that the needle valve holder screws down onto a copper washer. Anneal the washer if reusing. Heat to cherry red and...
17 Apr 2024
VicS
replied to the thread
Blake's seacock
.
Id not expect copper sulfate as it is moderately soluble in water... but it is bright blue. Copper chloride perhaps more likely than...
17 Apr 2024
VicS
replied to the thread
Can a Blake’s seacock be inadvertently installed so it closes anticlockwise?
.
It seems that although you have serviced the seacocks you have neglected the antisyphon valve(s) If they are the Jabsco type...
17 Apr 2024
VicS
replied to the thread
Plastic Laminate Adhesive
.
OTOH positioning will be easier, if that's an issue, than with a contact adhesive.
16 Apr 2024
VicS
replied to the thread
Plastic Laminate Adhesive
.
If you use the wood glue you will have to weight the laminate down evenly until the glue has dried . .
16 Apr 2024
VicS
replied to the thread
Can a Blake’s seacock be inadvertently installed so it closes anticlockwise?
.
Then your options are limited to closing with a part turn clockwise or a part turn anticlockwise depending which way up you fit the...
16 Apr 2024
VicS
replied to the thread
SS Richard Montgomery masts finally to be removed next year
.
Before they fall down and detonate the whole thing!
15 Apr 2024
Home
Members
Top