Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
C
Crinan12
Active member
Joined
6 Mar 2019
Last seen
Wednesday at 21:54
Messages
547
Reaction score
55
Points
28
Find
Find content
Find all content by Crinan12
Find all threads by Crinan12
Latest activity
Postings
About
C
Crinan12
reacted to
Neeves's post
in the thread
Arcona 460 sinks
with
Like
.
I would formally contact Arcona and ask them the questions you raise here. They have a problem, the problem is well documented. They...
14 Apr 2024
C
Crinan12
replied to the thread
Pss seal failure
.
I don't have much mechanical knowledge and I fitted one to my boat recently (while out of the water). My shaft just unbolted from my...
14 Apr 2024
C
Crinan12
replied to the thread
Pss seal failure
.
Wow unlucky. Do you have a y piece with a water feed and a breather? I can only see one pipe coming from yours? What boat? I understood...
14 Apr 2024
C
Crinan12
reacted to
LittleSister's post
in the thread
Soldering a pl259
with
Like
.
The important point about using the joint to melt the solder, rather than the iron, is that the solder will melt and run only when the...
4 Apr 2024
C
Crinan12
reacted to
LittleSister's post
in the thread
Soldering a pl259
with
Like
.
In my experience the typical cheap battery powered soldering iron, is v poor, almost useless. They might claim 90w but they might well...
3 Apr 2024
C
Crinan12
replied to the thread
Soldering a pl259
.
Thanks. I'll give this a go. I thought you melted the solder from the iron not the joint. I'll try again with some lead solder and flux...
3 Apr 2024
C
Crinan12
reacted to
VicS's post
in the thread
Soldering a pl259
with
Like
.
No wonder you are having trouble. The one I would use has bit about 3/16" diameter x 1" long. Wow that's the first time I've posted...
2 Apr 2024
C
Crinan12
replied to the thread
Soldering a pl259
.
I was trying to solder with the smaller pointy soldering iron tip, I will try the bigger flatter one. I don't think I've been getting...
2 Apr 2024
C
Crinan12
reacted to
habeer's post
in the thread
Soldering a pl259
with
Like
.
I use a 100 watt soldering gun. The PL259 has a lot of mass to heat up, and irons with a small tip (less than 3/16") won't get it done...
2 Apr 2024
C
Crinan12
replied to the thread
Soldering a pl259
.
Hi Chris we are at lochnell, was supposed to launch yesterday but when the yard went to put the mast on they found the new backstay is...
2 Apr 2024
C
Crinan12
reacted to
ctva's post
in the thread
Soldering a pl259
with
Like
.
Lead solder, good flux and a decent iron. Remember also a small tipped iron will lose heat very quickly to a surface it it trying to...
2 Apr 2024
C
Crinan12
reacted to
Martin_J's post
in the thread
Soldering a pl259
with
Like
.
Most definitely heat the larger part first I.e. the part of the plug instead of the wire. Also scrape the plating from the sides of...
2 Apr 2024
C
Crinan12
reacted to
Martin_J's post
in the thread
Soldering a pl259
with
Like
.
Try and apply solder then between the hot iron and the hot plug surface.. don't leave solder bubbling away on the iron if the plug part...
2 Apr 2024
C
Crinan12
replied to the thread
Soldering a pl259
.
90 watt apparently. It is 12 volt. Thanks
2 Apr 2024
C
Crinan12
replied to the thread
Soldering a pl259
.
It's a battery one I'm using Seems to get very hot -I burnt my fingers anyway Am I aiming to get the pl259 very hot as well? I.e. rest...
2 Apr 2024
Loading…
Loading…
Home
Members
Top