Recent content by chrisb1309

  1. C

    13” x10” 3 bladed LH prop on EBay. Item 234005744710

    If this would be of any use to you please have a look Now no longer required and am keen to find it a home,
  2. C

    Volvo MD1 Water pump impellers for sale ebay

    234002267690. Item on eBay Volvo penta part number. 803729-3. Also Johnson. 09-806B 3 impellers available
  3. C

    Water pump impeller for sale on EBay

    234002267690. Item on eBay Volvo penta part number. 803729-3. Also Johnson. 09-806B 3 impellers available
  4. C

    2 new Dynastart V belts for Volvo MD1

    I have two that have never been fitted. I changed engines, and am having a clear out. Fit onto the large flywheel and dynastart pulley. Hopefully of use to someone 10 mm wide and 1300mm circumference according to markings on belt. How about £7.50. Including postage to a UK address Have...
  5. C

    Three bladed LH propellor. 13” X10” excellent condition

    To fit 1” shaft , standard taper with 1/4” keyway. This prop was fitted for a few years before we changed engines. The replacement rotates in opposite sense, hence this prop is now surplus. It is virtually unmarked, polished bronze and is available either SW London or Near Chichester for...
  6. C

    Morse lever wanted

    Hi I have a two lever control that was fitted to VP MD1. It has a smaller throttle lever and large lever than both pushes and pulls that was connected to Gbox with Morse cable of approx 8.25mm inner diam ( not the usual 33c). Throttle lever used a 33c cable. Both levers can be pulled out of...
  7. C

    Avon redstart outboard bracket

    Hi, We have an Avon outboard bracket, grey plastic coated metal with wooden outboard mounting block. Son lost our dinghy! located south of Chichester Contact me if you are interested
  8. C

    New injector. Volvo. MD1. MD11

    Thanks for that info Scottie The Number stamped on the body is: KBL52S58/4. Body length. 51.7mm Body to tip: 73.6mm. Having now examined closely after unwrapping the injector I would describe it as "reconditioned" as the body has signs of having been fitted Chris
  9. C

    New injector. Volvo. MD1. MD11

    I have an unused injector for sale, I no longer have the MD1 so now surplus. I think this is as fitted to the 2 cylinder engine. £80 or best offer Please PM me for further details Chris
  10. C

    Refilling water jacket MD1

    Hi. We used to drain ours after each trip . On restarting,open seacock, having closed block tap and start. The jabsco would pump thro' after a while! We have now retired the old lump due to general overall fatigue . Have complete engine and gear box available if any one interested Chris
  11. C

    Dingy: Avon Rover R2.8

    PM sent
  12. C

    Yanmar 3YM30 Alternator

    Sending PM
  13. C

    Wichard Snatch Blocks

    PM sent Chris
  14. C

    Machining prop to fit shaft

    Thanks for all these suggestions. I know the taper as we had a new shaft and prop made by T Norris some years ago. It's the machining of the prop I've acquired that is the issue. As mentioned, it was suggested by a specialist that I would be advised to buy a new prop as the machining cost...
  15. C

    Machining prop to fit shaft

    Hi Folks I am in the process of re engining our westerly and require a RH prop. I have obtained a suitable used propellor but for a different shaft diameter. Any suggestions as to who would machine this to suit our shaft, at a reasonable price , would be well received. I have received one...
See more
Top