Warp sizes

whisper

New member
Joined
31 Aug 2002
Messages
5,163
Location
Stratford upon Avon & S.Devon
Visit site
Sorry to ask such a mundane question but I've searched these archives in vain.
Simple question is :- What diameter of anchor line and mooring lines should a 23ft , 2 tonne, deep V motor boat have? In Your Honest Opinion that is.
 

alanporter

New member
Joined
8 Jul 2002
Messages
324
Location
Victoria, BC, Canada
Visit site
Most authorities would recommend 3/8 inch (sorry, we haven't gone metric where I sail), twist laid nylon. Twist lay and nylon are important because they impart the necessary stretch that is required for both anchor and mooring line. Using thicker line reduces the stretch and thus puts more strain on your cleats etc.

Last Year at my club, a member moored his 27 foot sailboat with 5/8 double braid line. When the first winter storm came along, the line held but it tore a mooring cleat right out of the deck. It you use anything thicker than 3/8 inch, you must fit rubber snubbers.

I use 7/8 inch twist nylon on my seven ton 31 footer, and have had no problems in 26 years of year round sailing.

Alan Porter
 

Plum

Well-known member
Joined
6 Jun 2001
Messages
4,597
Location
UK East Coast
Visit site
12mm diameter. No need to any larger. In terms of strength you could go for a smaller diameter, but 12mm is about the smallest for comfotable handling. Polyester rope for mooring (longer life in the sun) and nylon for anchoring (more stretchy)
 

Plum

Well-known member
Joined
6 Jun 2001
Messages
4,597
Location
UK East Coast
Visit site
Yes, you could use Polypropylene, nothing particularly wrong with it. but this material degrades quicker in sunlight than nylon or polyester, tends not to be very good for throwing a coil of it ashore (it is light in weight and gets wrinkled easy) and is often rougher to handle.
Much of the above is personal preference. I have some warps of polyester and some of polypropylene and for usage and long term cost efficiency I prefer Polyester.
 

duncan

Active member
Joined
16 May 2001
Messages
9,443
Location
Home mid Kent - Boat @ Poole
Visit site
mine is 25 ft / 2.5 tons and I use 12mm octoplait because it is nice to handle.
Using the boat for fishing a fair bit in the winter, anchoring in big tides, 100ft of water, you really appreciate a nice warp.
You could get away with 10mm 3 ply nylon but it won't sit in your anchor locker so well and makes it less easy to pull up at the end of the day.
Buyu in bulk at the boat show - English braids will do a surprising deal if you ask and haul it away that day (rigged as a sholder carry load it's no big problem).
 

Bejasus

New member
Joined
9 Jun 2002
Messages
6,528
Location
Savannah 32 00.50N - 80 59.90W
Visit site
On my 25ft, 2-1/4 tonner, I use 12mm polyester on the stern and the same on fore & aft springs to a pile with rubber snubbers to allow the necessary stretch.

<A target="_blank" HREF=http://www.arweb.co.uk/argallery/h00>h00's Project</A>
 

ccscott49

Active member
Joined
7 Sep 2001
Messages
18,583
Visit site
12 mm braid on braid or multiplait or three strand polyester for your warps. A lot of people mention nylon for stretch for anchor warps, but as it stretches it causes internal heat, which weakens the rope, yes, even under water! Speak to somebody who really knows ropes and they will not reccomend nylon for long term anchor warps. You can also use a fender as a snubber, just wrap the warp around the fender a few turns, this will squash the fender, giving you a nice springy effect. You have fenders, snubbers cost money. I would also reccomend plastic pipe over the warps at chafe points, ie, though the fairleads, bow roller, cleats etc.
 
Top