jimi
Well-Known Member
If so I'd be only too pleased to pass the original on to the owner.
<hr width=100% size=1>.. whit way roon should it be again ..
<hr width=100% size=1>.. whit way roon should it be again ..
Anybody recognise this boat
- Thread starter jimi
- Start date
Keen_Ed
Well-Known Member
Looks like one of Ed Burnett's - Foxhound?
http://www.byd.btinternet.co.uk/byd-designs.htm
ed.burnett@btinternet.com
<hr width=100% size=1>
http://www.byd.btinternet.co.uk/byd-designs.htm
ed.burnett@btinternet.com
<hr width=100% size=1>
ParaHandy
Well-Known Member
is that a lady on the windward side and is she drawing your attention to something pertinent to your intended course ..?
<hr width=100% size=1>
<hr width=100% size=1>
longjohnsilver
Well-Known Member
Better enter it into Boatones competition.
Where did you take the pic?
<hr width=100% size=1>
Where did you take the pic?
<hr width=100% size=1>
Twister_Ken
Well-Known Member
What a shame...
...to have a rubadub towing behind. Should be a nice little varnished clinker pulling dinghy for a boat like that.
<hr width=100% size=1><A target="_blank" HREF=http://www.writeforweb.com/twister1>Let's Twist Again</A>
...to have a rubadub towing behind. Should be a nice little varnished clinker pulling dinghy for a boat like that.
<hr width=100% size=1><A target="_blank" HREF=http://www.writeforweb.com/twister1>Let's Twist Again</A>
ParaHandy
Well-Known Member
Not for long ...
.. perhaps? i have seen a dinghy of similar proportions and colour on his boat ...
<hr width=100% size=1>
.. perhaps? i have seen a dinghy of similar proportions and colour on his boat ...
<hr width=100% size=1>
Jacket
Well-Known Member
Yep, its Foxhound. Lovely boat- when I'm rich I'll get one. But I'll have to be very rich- £160,000 for a 30 footer!
<hr width=100% size=1>
<hr width=100% size=1>
jimi
Well-Known Member
Took it just outside the Helford River (I think)!
<hr width=100% size=1>.. whit way roon should it be again ..
<hr width=100% size=1>.. whit way roon should it be again ..
G
Guest
Guest
Just an aside ....
Anybody care to comment what may be wrong here in the picture ?
I of course could be wrong all these years .... interesting to see if anyone else says same !!
<hr width=100% size=1>Nigel ...
<A target="_blank" HREF=http://www.qqbaltic.com/index.html>http://www.qqbaltic.com/index.html</A> For all those disbelievers ! /forums/images/icons/cool.gif
Anybody care to comment what may be wrong here in the picture ?
I of course could be wrong all these years .... interesting to see if anyone else says same !!
<hr width=100% size=1>Nigel ...
<A target="_blank" HREF=http://www.qqbaltic.com/index.html>http://www.qqbaltic.com/index.html</A> For all those disbelievers ! /forums/images/icons/cool.gif
jimi
Well-Known Member
Re: Just an aside ....
Backstays?
<hr width=100% size=1>.. whit way roon should it be again ..
Backstays?
<hr width=100% size=1>.. whit way roon should it be again ..
rich
Well-Known Member
It's not moving..
<hr width=100% size=1>
<hr width=100% size=1>
Keen_Ed
Well-Known Member
Re: Just an aside ....
Well, the backstays are set up - the small black blob just below the main clew - so its not that.
I suppose there is a point of discussion on the length of the tender's painter?
<hr width=100% size=1>
Well, the backstays are set up - the small black blob just below the main clew - so its not that.
I suppose there is a point of discussion on the length of the tender's painter?
<hr width=100% size=1>
tome
Well-Known Member
Re: Just an aside ....
No, all looks good to me. Runners set up ok for stbd tack. On a Bermudan rig I'd be tempted to run a preventer, but not on a gaffer in these conditions.
<hr width=100% size=1>
No, all looks good to me. Runners set up ok for stbd tack. On a Bermudan rig I'd be tempted to run a preventer, but not on a gaffer in these conditions.
<hr width=100% size=1>
G
Guest
Guest
Arghhhhhh Bisto !!
I was always taught ...... flubbers hard up nose on transom to stop turning turtle in any wind, hard tenders on long painters - shorten in as you go into 'port'.
But I must admit that I do as in picture quite often !!!!!
It was only a bit of fun anyway !!!!
<hr width=100% size=1>Nigel ...
<A target="_blank" HREF=http://www.qqbaltic.com/index.html>http://www.qqbaltic.com/index.html</A> For all those disbelievers ! /forums/images/icons/cool.gif
I was always taught ...... flubbers hard up nose on transom to stop turning turtle in any wind, hard tenders on long painters - shorten in as you go into 'port'.
But I must admit that I do as in picture quite often !!!!!
It was only a bit of fun anyway !!!!
<hr width=100% size=1>Nigel ...
<A target="_blank" HREF=http://www.qqbaltic.com/index.html>http://www.qqbaltic.com/index.html</A> For all those disbelievers ! /forums/images/icons/cool.gif
