Habebty
Well-known member From Norfolk/Suffolk
- Joined
Latest activity Postings About
-
-
Habebty reacted to Ammonite's post in the thread How to cut a Larger Hole where there is already a smaller Hole! with
Like.
If #6 doesn't work for you or you want the larger hole slightly off centre. Screw a scrap strip of plywood over the existing hole with... -
Habebty reacted to Boathook's post in the thread How to cut a Larger Hole where there is already a smaller Hole! with Like.
Purchased this and actually used it to enlarge a hole. https://www.screwfix.com/p/starrett-a19-hole-enlargement-arbor-58-6mm/386rf
-
Habebty reacted to Refueler's post in the thread How to cut a Larger Hole where there is already a smaller Hole! with Like.
OK - two ways : If you can get back of the existing hole ... glue a thin piece of ply or material to cover the existing hole. But size...
-
Habebty replied to the thread How to cut a Larger Hole where there is already a smaller Hole!.Purchased this and actually used it to enlarge a hole. https://www.screwfix.com/p/starrett-a19-hole-enlargement-arbor-58-6mm/386rf...
-
Habebty reacted to Martin_J's post in the thread How to cut a Larger Hole where there is already a smaller Hole! with Like.
I would probably do the same as the two previous posters... If you were doing this every day, or just liked buying tools, perhaps look...
-
Habebty replied to the thread How to cut a Larger Hole where there is already a smaller Hole!.Funnily enough the above ideas popped into my head as soon as hit "post" !! despite thinking about it all day 😁
-
Habebty reacted to Sticky Fingers's post in the thread How to cut a Larger Hole where there is already a smaller Hole! with Like.
Make a jig out of small piece of scrap half inch ply or mdf by drilling it through with the hole cutter size you want, tape the jig...
-
Habebty reacted to Daydream believer's post in the thread How to cut a Larger Hole where there is already a smaller Hole! with Like.
Drill a hole with a hole cutter of the new size in a bit of 6mm ply. Clamp this over the position where you want it. You could screw it...
-
Habebty posted the thread How to cut a Larger Hole where there is already a smaller Hole! in Practical Boat Owner's Reader to Reader.I am fitting new instruments. I need to cut/drill a 92mm hole where there is already a 60mm hole in the GRP hatch garage. Bit tricky to...
-
Habebty replied to the thread £0.43 Fix for Meaco DD8L Dehumidifier.What I would like to know is how to ensure it starts up again after low temperature shutdown which is by design, It seems to shutdown at...
-
Habebty replied to the thread Fastnet 1979.Yes, Sailorman’s boat was indeed an Oyster called Jolie Brise.
-
Habebty replied to the thread The Black Deep and the PLA General Directions - Update.This….https://www.bbc.co.uk/news/articles/cm20pz5r0kxo
-
Habebty reacted to Poecheng's post in the thread The Black Deep and the PLA General Directions - Update with Like.
I am another entirely unaware of this and have transited merrily with AIS on without a squeak from them. I note the comments about...
-
Habebty replied to the thread The Black Deep and the PLA General Directions - Update.TG, Thanks for your efforts on this. Over the last twenty years or so crossing the Estuary, I have probably had to hang around twice for...
-
Because, the Hydrographic Office is withdrawing from the paper chart market. NV Charts, because of the thing that we dare not mention...
-
-
Loading…
-
Loading…