Wet Balsa Core

Mark Taylor

New member
Joined
17 Jan 2011
Messages
94
Location
Ayr
Visit site
I realised that a number of my deck fittings have been straight bolted through the sandwich without the core first having been removed and replaced with glass or a solid plywood pad or whatever, so...................Any ideas on how best to dry out sections of a balsa cored sandwich deck where there has been water leakage around fittings??

Mny thanks
Mark
 

saltylegs

Active member
Joined
23 Jan 2010
Messages
1,024
Location
Strangford Northern Ireland
Visit site
I realised that a number of my deck fittings have been straight bolted through the sandwich without the core first having been removed and replaced with glass or a solid plywood pad or whatever, so...................Any ideas on how best to dry out sections of a balsa cored sandwich deck where there has been water leakage around fittings??

Mny thanks
Mark

You won't be able to dry the balsa it will have gone soggy so you will need to cut out the core by removing the top or bottom skin, (I find the top easier) and remove the soggy goo and replace with new core material, if it is fairly flat ply is ok.
I am sure you will get lots of advice on here there are some photos of what I did on the link below. (sorry for having to go through them all but I have'nt perfected the single photo thing yet).
http://s1143.photobucket.com/albums/n630/saltylegs/
 

Sneaky Pete

Member
Joined
26 Nov 2009
Messages
854
Location
In the shadows of Faslane.
Visit site
Huge job time consuming but if you have good DIY knowledge and skill you could tackle it yourself. It basically involves identifying the area that has de-laminated, come away from the balsa, if the balsa is mush then it needs replacing that is done from inside the boat cutting out the area that has de-laminated. If it is damp it requires drilling a series of holes just inside the de-laminated area, allow to dry out completely bond with epoxy and fair the surface. There are a number of books on the matter. Pm me and I could send you some more info.
 

dgadee

Well-known member
Joined
13 Oct 2010
Messages
3,895
Visit site
I had two minor bits - got the wet stuff out with a bit of poking from a hex key. Don Casey's Hull and Deck Repair was a good help and good value.
 

john_morris_uk

Well-known member
Joined
3 Jul 2002
Messages
27,858
Location
At sea somewhere.
yachtserendipity.wordpress.com
It also depends on how far the sogginess has gone. I have had some success with taking the fitting out and removing the balsa with a bent wire/nail/allan key etc etc until you get to sound dry wood. If you are lucky and the access hole is 10 or 12 mm then you can get quite a bit of balso out and its obvious when you get to dry stuff. Then dry it out with a hot air gun (be careful not to over heat the GRP) and seal the bottom hole with tape and fill the void with thickened epoxy. Drill through the epoxy when set to remount the deck fitting - job done.
 

Koeketiene

Well-known member
Joined
24 Sep 2003
Messages
18,007
Location
Le Roussillon (South of France)
www.sailblogs.com
I realised that a number of my deck fittings have been straight bolted through the sandwich without the core first having been removed and replaced with glass or a solid plywood pad or whatever, so...................Any ideas on how best to dry out sections of a balsa cored sandwich deck where there has been water leakage around fittings??

Mny thanks
Mark

This article is fairly comprehensive and should you give a good idea of what's involved.

Good luck
 

Mark Taylor

New member
Joined
17 Jan 2011
Messages
94
Location
Ayr
Visit site
Many thanks for all the advice which is much appreciated - looks like I'm going to be getting very dusty over the next few months!!

regards
 

Sneaky Pete

Member
Joined
26 Nov 2009
Messages
854
Location
In the shadows of Faslane.
Visit site
It also depends on how far the sogginess has gone. I have had some success with taking the fitting out and removing the balsa with a bent wire/nail/allan key etc etc until you get to sound dry wood. If you are lucky and the access hole is 10 or 12 mm then you can get quite a bit of balso out and its obvious when you get to dry stuff. Then dry it out with a hot air gun (be careful not to over heat the GRP) and seal the bottom hole with tape and fill the void with thickened epoxy. Drill through the epoxy when set to remount the deck fitting - job done.

Can I add to this a bent nail works well you could fit it to a cordless drill where it will do the job of cleaning out fairly quickly, an alternative to filling the hole completely is to pack the thickened epoxy into where the balsa core filler was leaving the hole untouched it saves drilling later on one advantage of filling the core is that should the fitting leak again the water will pass down the bolt and into the boat making it quicker and easier to spot without damaging the core.
 

john_morris_uk

Well-known member
Joined
3 Jul 2002
Messages
27,858
Location
At sea somewhere.
yachtserendipity.wordpress.com
Can I add to this a bent nail works well you could fit it to a cordless drill where it will do the job of cleaning out fairly quickly, an alternative to filling the hole completely is to pack the thickened epoxy into where the balsa core filler was leaving the hole untouched it saves drilling later on one advantage of filling the core is that should the fitting leak again the water will pass down the bolt and into the boat making it quicker and easier to spot without damaging the core.
I should have made it clear that I also meant 'put the bent wire/nail/Allan key I into a cordless drill'.
 
Top