Nut size on 1.5” heads outlet skin fitting

wizard

Well-known member
Joined
24 Jan 2003
Messages
1,695
Location
Portland
Visit site
As above to remove old skin fitting and/or tighten new skin fitting as I am replacing all in DZR.

Also, it is in a slight depression so I think an offset spanner is required. Any suggestions of where to get it from?
 

Boater Sam

Well-known member
Joined
14 Mar 2020
Messages
1,487
Location
Philippines and Thailand
Visit site
As above to remove old skin fitting and/or tighten new skin fitting as I am replacing all in DZR.

Also, it is in a slight depression so I think an offset spanner is required. Any suggestions of where to get it from?
Box spanners are the answer. Size will depend on the fitting, there is no standard for nut sizes on BSP fittings.
 

lustyd

Well-known member
Joined
27 Jul 2010
Messages
12,403
Visit site
They don't need to be crazy tight when fitting, the sika will hold it in place once cured so any tool that can get it better than hand tight is fine. Undoing them I used a pipe wrench/stilsons. Boater Sam is right, Box spanner probably is the better answer but a set that big is quite pricey and probably won't fit in the gaps you have anyway!
When fitting, don't forget that if you're using a tool on the inside you'll also need a tool on the outside and a friend to hold that tool. A sika'd up skin fitting is round and slippery so look into what tools you can get for your skin fittings. For what it's worth I couldn't get the tools for my Trudesign (which have a special, but cheap tool) so we ended up just holding them and tightening by hand and they're all good and tight and have not leaked at all.
 

lustyd

Well-known member
Joined
27 Jul 2010
Messages
12,403
Visit site
An angle grinder on the outside of the hull will get it off much quicker
Having done this job recently I can confidently say it really doesn’t. It takes a lot of work to grind out a bronze seacock and makes an enormous mess while also heating up the glass to levels I felt uncomfortable with. A pipe wrench took about 30 seconds per fitting and made zero mess. The only exception in my opinion is where there isn’t space for the wrench.
 

Pye_End

Well-known member
Joined
5 Feb 2006
Messages
5,145
Location
N Kent Coast
Visit site
Get a large adjustable like this: 6-68mm Adjustable Large Spanner Wrench Opening Bathroom Nut Key DIY Hand Tool 7427274574632 | eBay

A tool you can then use with other sizes of big nuts.

Grinding off the flange: sometimes you try to get the whole thing off with tools, and it doesn't take too long. Sometimes you think it will be quick, and realise after it took a long time in comparrison, or you give up as being too hard (but you don't always know which when you start). Grinding helps with a little technique - ie focus on the corner rather than whole flange - quick and easy, particularly compared with a stubborn interior.
 

plumbob

Well-known member
Joined
18 Oct 2009
Messages
1,277
Location
Bucks
Visit site
Get a large adjustable like this: 6-68mm Adjustable Large Spanner Wrench Opening Bathroom Nut Key DIY Hand Tool 7427274574632 | eBay

A tool you can then use with other sizes of big nuts.

Grinding off the flange: sometimes you try to get the whole thing off with tools, and it doesn't take too long. Sometimes you think it will be quick, and realise after it took a long time in comparrison, or you give up as being too hard (but you don't always know which when you start). Grinding helps with a little technique - ie focus on the corner rather than whole flange - quick and easy, particularly compared with a stubborn interior.
I have one of those. Never realised it was so cheap.👍
 

wizard

Well-known member
Joined
24 Jan 2003
Messages
1,695
Location
Portland
Visit site
Get a large adjustable like this: 6-68mm Adjustable Large Spanner Wrench Opening Bathroom Nut Key DIY Hand Tool 7427274574632 | eBay

A tool you can then use with other sizes of big nuts.

Grinding off the flange: sometimes you try to get the whole thing off with tools, and it doesn't take too long. Sometimes you think it will be quick, and realise after it took a long time in comparrison, or you give up as being too hard (but you don't always know which when you start). Grinding helps with a little technique - ie focus on the corner rather than whole flange - quick and easy, particularly compared with a stubborn interior.


Thanks, that sounds like the perfect answer to the problem.
 
Top