Home
Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Navigation
Install the app
Install
More options
Contact us
Close Menu
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Ian_Edwards
Well-known member
·
From
Aberdeen Scotland
Joined
9 Feb 2002
Last seen
Today at 12:23
Messages
2,008
Reaction score
263
Points
83
Find
Find content
Find all content by Ian_Edwards
Find all threads by Ian_Edwards
Latest activity
Postings
About
Ian_Edwards
replied to the thread
Gas regulators, when to replace?
.
Thanks VicS, that's the number I was looking for. I get a gas safety engineer to check the gas system on the boat, every two years. He...
Yesterday at 18:49
Ian_Edwards
posted the thread
Gas regulators, when to replace?
in
Practical Boat Owner's Reader to Reader
.
I found two gas regulators when clearing my garage. One is stamped 8 07, the other 01 00. I guess these codes are the date of...
Yesterday at 10:25
Ian_Edwards
replied to the thread
Mast Tabernacle-Any downsides?
.
I had a tabernacle on my Parker 275. I used it every spring and autumn to lower an raise the mast. As other has said it is very...
Sunday at 22:21
Ian_Edwards
reacted to
Sandy's post
in the thread
Producing Victron Schematic drawings?
with
Like
.
I use a piece of paper a pencil and eraser.
7 Dec 2024
Ian_Edwards
replied to the thread
Siting a fluxgate compass
.
I had a similar problem. The Southerly has a 4ton cast steel plate recessed into the hull, and a 2.5 ton cast steel centre board. The...
6 Dec 2024
Ian_Edwards
reacted to
SteveA's post
in the thread
Brass Screw Heads on Raw Water Pump
with
Like
.
These little brass screws are a pain but you might try an impact screwdriver to get them moving. I've never had much success with stud...
5 Dec 2024
Ian_Edwards
reacted to
thinwater's post
in the thread
Using GPS with gloves
with
Like
.
Yes, I have used them. The other problem with touch screens is how sensitive they are to finger moisture. Too wet or too dry they don't...
5 Dec 2024
Ian_Edwards
reacted to
thinwater's post
in the thread
Using GPS with gloves
with
Like
.
This is just one of the ways in which touch screens and menu-driven stuff sucks. I've had them. IMO, any gear that cannot be operated...
5 Dec 2024
Ian_Edwards
replied to the thread
Epoxy repair kit?
.
Yes, it's made by West. I have a kit on board, it's been open for at least 2 years, and I use a little now and again, last time in March...
4 Dec 2024
Ian_Edwards
reacted to
Aquanaught's post
in the thread
Expensive watches on boats.
with
Like
.
By all means buy your expensive watch but wear it only for evenings ashore etc. Have a cheap waterproof watch for daily wear as it's...
4 Dec 2024
Ian_Edwards
replied to the thread
Epoxy repair kit?
.
G-Flex make small kits of thickened epoxy. The two components come in tubes, and it's easy to mix small quantities. I find it a lot less...
4 Dec 2024
Ian_Edwards
replied to the thread
Drying your teak deck out to caulk bits of it over the UK winter
.
This may be an unconventional approach. My boat developed a leaking teak deck in 2023. I sort advice on this forum and bought a Fein...
3 Dec 2024
Ian_Edwards
replied to the thread
Emergency start packs ?
.
I have one as in #2. It has started both my old Subaru 2L diesel and the 2.2L Yanmar 4jh4e. I've only needed it twice in 4, perhaps 5...
3 Dec 2024
Ian_Edwards
replied to the thread
Blackout curtains ruined?
.
A slight digression. The windows on the Southerly have wooden frames on the inside. I made blackout boards out of light weight foam...
1 Dec 2024
Ian_Edwards
reacted to
thinwater's post
in the thread
Dinghy trot knot
with
Like
.
Brainstorming... A prusik hitch and a carabiner might be faster and at least as secure. A rolling hitch or camel hitch with a half...
28 Nov 2024
Loading…
Loading…
Home
Members
Top